中科因仑“3+1”工程特种兵精英论坛

标题: STM32LXXX系列低功耗测试代码 [打印本页]

作者: 张衍波 时间: 2015-5-20 08:20
标题: STM32LXXX系列低功耗测试代码
拿到STM32L的样片后，一直纠结于低功耗的测试，因为和STM32F系列的配置不同，所以导致了杯具，通过和ST公司不停的咨询，终于得到了最终的结果，
经过测试，功耗在STOP模式下为 500nA ，性能还是不错的，代码如下：

/**
  * @brief  Main program.
  * @param  None
  * @retval None
  */
int main(void)
{
  /*!< At this stage the microcontroller clock setting is already configured,
   this is done through SystemInit() function which is called from startup
   file (startup_stm32l1xx_md.s) before to branch to application main.
   To reconfigure the default setting of SystemInit() function, refer to
   system_stm32l1xx.c file
   */
   /* Configure all unused GPIO port pins in Analog Input mode (floating input
   trigger OFF), this will reduce the power consumption and increase the device
   immunity against EMI/EMC *************************************************/
GPIO_InitTypeDef GPIO_InitStructure;
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA | RCC_AHBPeriph_GPIOB | RCC_AHBPeriph_GPIOC

                     | RCC_AHBPeriph_GPIOD | RCC_AHBPeriph_GPIOE | RCC_AHBPeriph_GPIOH, ENABLE);

/* config all IO to Analog Input to reduce parasite power consumption */

GPIO_InitStructure.GPIO_Pin = GPIO_Pin_All;

GPIO_InitStructure.GPIO_Speed = GPIO_Speed_400KHz;

GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;

GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;

GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;

GPIO_Init(GPIOC, &GPIO_InitStructure);

GPIO_Init(GPIOD, &GPIO_InitStructure);

GPIO_Init(GPIOE, &GPIO_InitStructure);

GPIO_Init(GPIOH, &GPIO_InitStructure);

GPIO_Init(GPIOA, &GPIO_InitStructure);

GPIO_Init(GPIOB, &GPIO_InitStructure);

/* Enable PB7 as external PVD input so as to set it as AIN_IN */
Set_PVD_To_Config_PB7();

RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA
                        | RCC_AHBPeriph_GPIOB
                        | RCC_AHBPeriph_GPIOC
                        | RCC_AHBPeriph_GPIOD
                        | RCC_AHBPeriph_GPIOE
                        | RCC_AHBPeriph_GPIOH, DISABLE);

PWR_UltraLowPowerCmd(ENABLE);
PWR_EnterSTOPMode(PWR_Regulator_LowPower, PWR_STOPEntry_WFI);
while(1);
}
/**
  * @brief  Enable PB7 as external PVD input so as to set it as AIN_IN
  * @param  None
  * @retval None
  */
void Set_PVD_To_Config_PB7(void)
{
  RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);

  /* Configure the PVD Level to 3 (2.5V) */
  PWR_PVDLevelConfig(PWR_PVDLevel_7);

  /* Enable the PVD Output */
  PWR_PVDCmd(ENABLE);
}
转载

欢迎光临中科因仑“3+1”工程特种兵精英论坛 (http://bbs.enlern.com/)